This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
cso:instruments:heterodyne:sidecab_rxb [2013-11-23 01:18]
cso:instruments:heterodyne:sidecab_rxb [2014-04-16 22:23] (current)
Line 1: Line 1:
 +====== Wide Band Sidecab Receivers ======
 +The 230 GHz and 460 GHz wide band sidecab receivers are housed in a single cryostat. They have 4 GHz bandwidths (4-8 GHz IF) and synthesized local oscillators. They were installed in 2012 May. 
 +These receivers are tuned automatically by a dedicated computer. Receiver tuning takes about a minute. For example to observe [[wideband#​example_1|three CO isotopologues]] [<​sup>​12</​sup>​CO(2-1) in the USB flanked by <​sup>​13</​sup>​CO(2-1) and C<​sup>​18</​sup>​O(2-1) in the LSB],\\
 +''​__uip__>​ **instr rx230b**''​\\ ​
 +''​__uip__>​ **lo 12co2-1 /if 5.28 /side up**''​\\ ​
 +''​__uip__>​ **spectrometer /ffts1w 5.28 /ffts2 /restart **''​\\
 +Both FFT spectrometers,​ [[ffts1|FFTS1]] and [[ffts2|FFTS2]],​ are available with these receivers. The [[aos5|AOS5]] is not available. FFTS1 is switched between the receivers automatically.
 +One half of FFTS2 (sub bands 1 and 2) is connected to the 230 GHz receiver and the other half (sub bands 3 and 4) is connected to the 460 GHz receiver. ​
 +To point using the [[ffts2|FFTS2]],​ specify the channel range corresponding to the appropriate sub band  with the ''​HALF_WIDTH''​ argument and ''/​CENTER''​ option or with the ''/​RANGE''​ option. For example, with FFTS2B3 (connected to the 460 GHz receiver):​\\
 +''​__uip__>​ **five_point 10 /range 16385 24576 /ffts2 **''​
 +The same pointing file (''​230b_460b.pointing_setup''​) is used for both the 230 GHz and the 460 GHz receivers. In principle, the beams are coaligned.
 +When switching between the 230 GHz and 460 GHz receivers or to turn off the receiver at the end of night, use\\
 +''​__uip__>​ **lo /​off**''​
 +==== Caveat ====
 +With the 230 GHz receiver, observing at frequencies below 210 GHz requires manual installation of an extra low pass filter in the LO chain. Otherwise there will be spurious response at higher frequencies,​ near 4/3 x LO frequency. Please consult with the staff for details.
 +==== Troubleshooting ====
 +When using the 460 GHz receiver with FFTS1, verify the correct input (A3) is shown on the display panel of the FFTS1 IF processor.
 +If the receiver tuning completes but the receiver has no sensitivity on the sky, it is possible the synthesizer output is turned off. To reset the power level and reenable the output, switch to a different local oscillator (phase lock) system and back:\\
 +''​__uip__>​ **lo /lock_loop default** ''​ \\
 +''​__uip__>​ **lo /lock_loop synthesized_lo** ''​
 +As long as the LO command is able to communicate with the receiver computer, you do not need to interact with it directly. If the LO command throws exceptions relating to communication with the receiver computer, reestablish the connection using\\
 +''​__UIP__>​ **lo /restart **''​
 +If you still receive exceptions after issuing the above command, you may have to reboot the receiver computer. The receiver computer is located in the backend room on the second floor. After reboot, the receiver control software will automatically start up. Issue the above command to establish the connection.
 +For engineering and troubleshooting purposes, the vncviewer can be used to control the receivers directly or watch debug messages. Consult staff.\\
 +''​$ **vncviewer -shared XX.XX.XX.XX:​1 **''​
cso/instruments/heterodyne/sidecab_rxb.txt · Last modified: 2014-04-16 22:23 by admin
Recent changes RSS feed Donate Powered by PHP Valid XHTML 1.0 Valid CSS Driven by DokuWiki